ifup - bring a network interface up
ifdown - take a network interface down
ifquery - parse interface configuration
[-nv] [--no-act] [--verbose] [-i
ifdown [-nv] [--no-act] [--verbose] [-i FILE|--interfaces=FILE] [--state-dir=DIR] [--allow CLASS] -a|IFACE...
ifquery [-nv] [--no-act] [--verbose] [-i FILE|--interfaces=FILE] [--state-dir=DIR] [--allow CLASS] -a|IFACE...
ifquery -l|--list [-nv] [--no-act] [--verbose] [-i FILE|--interfaces=FILE] [--state-dir=DIR] [--allow CLASS] -a|IFACE...
ifquery --state [IFACE...]
The ifup and ifdown commands may be used to configure (or, respectively, deconfigure) network interfaces based on interface definitions in the file /etc/network/interfaces. ifquery command may be used to parse interfaces configuration.
A summary of
options is included below.
If given to ifup, affect all interfaces marked auto. Interfaces are brought up in the order in which they are defined in /etc/network/interfaces. Combined with --allow, acts on all interfaces of a specified class instead. If given to ifdown, affect all defined interfaces. Interfaces are brought down in the order in which they are currently listed in the state file. Only interfaces defined in /etc/network/interfaces will be brought down.
Force configuration or deconfiguration of the interface.
If any of the commands of scripts fails, continue.
Show summary of options.
Only allow interfaces listed in an allow-CLASS line in /etc/network/interfaces to be acted upon.
-i FILE, --interfaces=FILE
Read interface definitions from FILE instead of from /etc/network/interfaces.
Keep interface state in DIR instead of in /run/network.
-X PATTERN, --exclude=PATTERN
Exclude interfaces from the list of interfaces to operate on by the PATTERN. PATTERN uses a usual shell glob syntax. If shell wildcards are not used, it must match the exact interface name. This option may be specified multiple times resulting in more than one pattern being excluded.
Set OPTION to VALUE as though it were in /etc/network/interfaces.
Don’t configure any interfaces or run any "up" or "down" commands.
Don’t run any mappings. See interfaces(5) for more information about the mapping feature.
Don’t run any scripts under /etc/network/if-*.d/
Disable special handling of the loopback interface. By default, the loopback interface (lo on Linux) is predefined internally as an auto interface, so it’s brought up on ifup -a automatically. In the case the loopback device is redefined by user, the interface is configured just once anyway. If, however, another interface is also defined as loopback, it’s configured as usual. Specifying this option disables this behaviour, so the loopback interface won’t be configured automatically.
Show copyright and version information.
Show commands as they are executed.
For ifquery, list all the interfaces which match the specified class. If no class specified, prints all the interfaces listed as auto.
For ifquery, dump the state of the interfaces. When no interfaces specified, lists all interfaces brought up together with logical interfaces assigned to them and exits with a status code indicating success. If one or more interfaces specified, display state of these interfaces only; successful code is returned if all of interfaces given as arguments are up. Otherwise, 0 is returned.
Bring up all the interfaces defined with auto in /etc/network/interfaces
Bring up interface eth0
Bring up interface eth0 as logical interface home
Bring down all interfaces that are currently up.
Print names of all interfaces specified with the auto keyword.
ifquery -l --allow=hotplug
Print names of all interfaces specified with the allow-hotplug keyword.
Display the interface options as specified in the ifupdown configuration. Each key-value pair is printed out on individual line using ": " as separator.
ifup, ifdown, and ifquery are actually the same program called by different names.
The program does not configure network interfaces directly; it runs low level utilities such as ip to do its dirty work.
When invoked, ifdown checks if ifup is still running. In that case, SIGTERM is sent to ifup.
During interface deconfiguration, ifdown ignores errors the same way as if --ignore-errors was specified.
definitions of network interfaces See interfaces(5) for more information.
current state of network interfaces
The program keeps records of whether network interfaces are up or down. Under exceptional circumstances these records can become inconsistent with the real states of the interfaces. For example, an interface that was brought up using ifup and later deconfigured using ifconfig will still be recorded as up. To fix this you can use the --force option to force ifup or ifdown to run configuration or deconfiguration commands despite what it considers the current state of the interface to be.
The file /run/network/ifstate must be writable for ifup or ifdown to work properly. If that location is not writable (for example, because the root filesystem is mounted read-only for system recovery) then /run/network/ifstate should be made a symbolic link to a writable location. If that is not possible then you can use the --force option to run configuration or deconfiguration commands without updating the file.
Note that the program does not run automatically: ifup alone does not bring up interfaces that appear as a result of hardware being installed and ifdown alone does not bring down interfaces that disappear as a result of hardware being removed. To automate the configuration of network interfaces you need to install other packages such as udev(7) or ifplugd(8).
The ifupdown suite was written by Anthony Towns <email@example.com>.
interfaces(5), ip(8), ifconfig(8).