reboot - reboot or enable/disable Ctrl-Alt-Del
/* Since kernel
version 2.1.30 there are symbolic names LINUX_REBOOT_*
for the constants and a fourth argument to the call: */
int reboot(int magic, int magic2, int cmd, void *arg);
/* Under glibc
and most alternative libc’s (including uclibc,
musl and a few others), some of the constants involved have gotten
symbolic names RB_*, and the library call is a 1-argument
wrapper around the system call: */
int reboot(int cmd);
The reboot() call reboots the system, or enables/disables the reboot keystroke (abbreviated CAD, since the default is Ctrl-Alt-Delete; it can be changed using loadkeys(1)).
This system call fail (with the error EINVAL) unless magic equals LINUX_REBOOT_MAGIC1 (that is, 0xfee1dead) and magic2 equals LINUX_REBOOT_MAGIC2 (that is, 672274793). However, since 2.1.17 also LINUX_REBOOT_MAGIC2A (that is, 85072278) and since 2.1.97 also LINUX_REBOOT_MAGIC2B (that is, 369367448) and since 2.5.71 also LINUX_REBOOT_MAGIC2C (that is, 537993216) are permitted as values for magic2. (The hexadecimal values of these constants are meaningful.)
argument can have the following values:
(RB_DISABLE_CAD, 0). CAD is disabled. This means that the CAD keystroke will cause a SIGINT signal to be sent to init (process 1), whereupon this process may decide upon a proper action (maybe: kill all processes, sync, reboot).
(RB_ENABLE_CAD, 0x89abcdef). CAD is enabled. This means that the CAD keystroke will immediately cause the action associated with LINUX_REBOOT_CMD_RESTART.
(RB_HALT_SYSTEM, 0xcdef0123; since Linux 1.1.76). The message "System halted." is printed, and the system is halted. Control is given to the ROM monitor, if there is one. If not preceded by a sync(2), data will be lost.
(RB_KEXEC, 0x45584543, since Linux 2.6.13). Execute a kernel that has been loaded earlier with kexec_load(2). This option is available only if the kernel was configured with CONFIG_KEXEC.
(RB_POWER_OFF, 0x4321fedc; since Linux 2.1.30). The message "Power down." is printed, the system is stopped, and all power is removed from the system, if possible. If not preceded by a sync(2), data will be lost.
(RB_AUTOBOOT, 0x1234567). The message "Restarting system." is printed, and a default restart is performed immediately. If not preceded by a sync(2), data will be lost.
(0xa1b2c3d4; since Linux 2.1.30). The message "Restarting system with command '%s'" is printed, and a restart (using the command string given in arg) is performed immediately. If not preceded by a sync(2), data will be lost.
(RB_SW_SUSPEND, 0xd000fce1; since Linux 2.5.18). The system is suspended (hibernated) to disk. This option is available only if the kernel was configured with CONFIG_HIBERNATION.
Only the superuser may call reboot().
The precise effect of the above actions depends on the architecture. For the i386 architecture, the additional argument does not do anything at present (2.1.122), but the type of reboot can be determined by kernel command-line arguments ("reboot=...") to be either warm or cold, and either hard or through the BIOS.
inside PID namespaces
Since Linux 3.4, if reboot() is called from a PID namespace other than the initial PID namespace with one of the cmd values listed below, it performs a "reboot" of that namespace: the "init" process of the PID namespace is immediately terminated, with the effects described in pid_namespaces(7).
The values that
can be supplied in cmd when calling reboot()
in this case are as follows:
The "init" process is terminated, and wait(2) in the parent process reports that the child was killed with a SIGHUP signal.
The "init" process is terminated, and wait(2) in the parent process reports that the child was killed with a SIGINT signal.
For the other cmd values, reboot() returns -1 and errno is set to EINVAL.
For the values of cmd that stop or restart the system, a successful call to reboot() does not return. For the other cmd values, zero is returned on success. In all cases, -1 is returned on failure, and errno is set appropriately.
Problem with getting user-space data under LINUX_REBOOT_CMD_RESTART2.
Bad magic numbers or cmd.
The calling process has insufficient privilege to call reboot(); the caller must have the CAP_SYS_BOOT inside its user namespace.
reboot() is Linux-specific, and should not be used in programs intended to be portable.
systemctl(1), systemd(1), kexec_load(2), sync(2), bootparam(7), capabilities(7), ctrlaltdel(8), halt(8), shutdown(8)
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.